themesfert.blogg.se - Anytune 6666

#ANYTUNE 6666 INSTALL#
#ANYTUNE 6666 DRIVER#
#ANYTUNE 6666 FULL#
#ANYTUNE 6666 PC#

When the radio is on standby, turn SQ outer shaft clockwise to adjust the squelch level. Turn it clockwise to increase gain, and anti-clockwise to reduce the gain. When the radio is receiving, turn RFG inner shaft to adjust RF gain. Turn it clockwise to increase power, and anti-clockwise to reduce power. When the radio is transmitting, turn PWR outer shaft to adjust power. Note: Adjust the volume during communication to get a suitable level. The LCD displays VOL: XX (XX stands for the volume level, total 1-36 levels). When the radio is turned on, turning VOL clockwise will increase the volume, turn VOL anti-clockwise will reduce the volume.

Turn VOL anti-clockwise to switch off the radio, the radio is OFF.

When the LCD displays frequency or channel, the radio is on.

Turn VOL clockwise to switch on the radio, the radio emits a beep.

21 M Appears when using memory channels 22 REP Appears when the repeater function is ON. 18 IOk Appears when the +10Khz function is ON. 17 Appears when the Keypad lock function is ON. 16 ECHO Appears when the Echo function is ON. 15 EMG Appears when using the Emergency channel. 14 HIC Appears when the Hi-cut function is ON. 11 NB Appears when adjusting Noise Blanker is ON. 10 DW Appears when the Dual-watch function is ON. 2 RT This appears when adjusting SSB clarifier frequency.

#ANYTUNE 6666 PC#

Rear Panel 18 PC Cable Jack 19 External Speaker Jack 20 Antenna Jackġ F Appears when pressing the MENU key. 15 RX/TX Indicator 16 Microphone Jack 17 LCD Display 9 PWR RF Power Control 10 RFG RF Gain Control 11 SQ Squelch Control 12 CLAR SSB Clarifier switch 13 VOL/OFF Power On/Off Volume Control. Key Functions 1 MEM Use, store or delete memory channel 2 MODE Switch mode: FM、AM、USB、LSB、PA 3 BAND Switch band: A-I 4 FRQ Switch between channel mode and frequency mode 5 MENU Function Menu key 6 SCAN Scan, Scan add, Scan delete 7 DW Dual-watch scan, Dual-watch setup 8 EMG Emergy Channel Keypad lock. Locate the external speaker in a suitable place.

If using an external speaker, please choose an 8-ohm speaker with a 3.5mm monoband (double cable) plug. Using supplied self-tapping screws and pads(2 sets) to fix the hanger Be sure to use the suggested fuse, or it might damage the radio.Ĭhoose an ideal location that will not interfere with the driver.Replace the broken fuse with a good one, and close the fuse holder.Pull the two fuse covers in a different direction and open them.If newly installed fuses continue to blow, disconnect the power cable and contact your authorized dealer or an authorized service center. If the fuse blows, determine the reason, then correct the problem.Īfter the problem is resolved, replace the fuse.

#ANYTUNE 6666 FULL#

▲ Use a full power cable even if it is longer than needed, do not take off the fuse holder from the cable. ▲ Locate the power cable away from high temperature, moisture, portfire, and cable insulator. ▲ We suggest not using a cigar lighter as it often brings down the voltage.

Connect the negative black power cable with the – terminal of the battery.

Connect the positive red power cable with the + terminal of the battery.

This radio adopts a 13.8V power supply, never connect it to a 24V battery, And the 13.8V car battery shall with sufficient current, or the LCD will become dark and Transmit power will drop down.

The position of the antenna can be put as the following example:.

▲ Be sure to choose a matching antenna, you may inquiry our dealers. ▲ To avoid the risk of fire, electric shock, and radio damage, all base stations shall equip with a lightning protector

▲ Connect the antenna first before transmitting, or it might damage the radio. Grounding the antenna system to ensure the best performance of this radio.Screw the antenna connector into the antenna jack.To match with the radio, the antenna and cable shall with a characteristic impedance of 50ohm, or the antenna system will coefficient enough and will disturb TV, radio, or other electronics.

#ANYTUNE 6666 INSTALL#

Choose a suitable angle by the 3 screw holes in the two ends of the bracket.īefore using this radio, please install a highly efficient and harmonious adjusted CB antenna, the suitable antenna type, and correct installation will bring excellent communication.

Then insert the adjusting screws and check carefully each screw, making sure the screws and machine will not loose when the car shakes.

Put the Non-slip mat on the 2 ends of the bracket and put in the radio.

Using the self-tapping screws and pads(2 sets) to fix the bracket.

#ANYTUNE 6666 DRIVER#

Your radio should not interfere with the driver or crash the driver’s knee or leg when rush brake. Choose the most appropriate setting from a simple and practical point of view.